考虑水平（切向）位移影响的垫层孔隙内土工膜顶胀

The common cushion layer used in the geomembrane face rockfill dam is made of granular materials such as gravel and non-fine concrete where bulge deformation or failure of geomembrane is very likely to occur in its surface holes. The curve intersection method based on the thin film theory is the common method used to analyze the bulge deformation of the geomembrane in the surface holes of cushion layer. However, it is inaccurate due to the neglection of horizontal (tangential) displacement of the geomembrane. Based on the FEM theory, a new method is proposed, which takes the horizontal (tangential) displacement of geomembrane into consideration, and is validated by the bulge tests on the geomembrane in a circular hole. The deformations and strains of the geomembrane in different shapes of holes are analyzed by this method, and different strain distributions and failure modes are obtained. The curve intersection method is also used to compare with the new method under the same condition. It is indicated that there is less difference in the deformation and average strain of the geomembrane when the water pressure is low. However, when the water pressure is relatively high, the influences of horizontal (tangential) displacement of the geomembrane on its strain should not be neglected.     

Advances in analysis of total uncertainties in a semi‐invasive residual stress measurement method

The ability to characterise residual stress distribution accurately and over different length scales, particularly deep into an engineering part, plays a significant role in assessing structural integrity. Two most commonly used techniques to measure residual stress fields deep into engineering components include neutron diffraction (ND) and deep‐hole drilling (DHD). As the measurements depend on several physical quantities, they are susceptible to error. The error or uncertainties may turn substantial and compromise the suitability of the results. Although noninvasive, the neutron diffraction technique is neither readily available nor portable and is limited to approximately 60‐mm‐thick specimen; errors associated with results become unacceptable at greater flight paths. Moreover, a mock‐up representing the engineering component is normally used in the ND technique. In contrast, the DHD technique is portable and measures residual stresses with high spatial resolution. An error propagation technique was applied to develop an error analysis procedure taking into consideration various stages of the DHD method and successfully applied to different DHD measurements. An essential feature comprising the effect of plasticity due to the creation of reference hole in the DHD procedure has not yet been taken into account in the error analysis procedure. This paper briefly describes how the uncertainties due to the creation of the initial reference hole can be determined. The effect of plasticity in the drilling procedure is quantified in this study. This error is combined with other sources of error and formulated to determine the total error. An incremental DHD technique was used to measure the complex triaxial residual stress field in an as‐welded circular disc, and the measured data were used to illustrate the total error using the error analysis method developed in the study.     

Multislip and Soret–Dufour influence on nonlinear convection flow of MHD dissipative Casson fluid over a slendering stretching sheet with generalized heat flux phenomenon

In the present investigation, Soret–Dufour and multislip's impact on magnetohydrodynamics (MHD) Casson fluid flow encompassing variable thermophysical features in the nonlinear convection process is analyzed. It is believed that to any effective heat and mass transfer enhancement, the relaxation of such fluid and material time along with the thermo-physical features, are well estimated. In this model, a magnetic field of nonuniform strength is applied perpendicular to the slendering sheet with variable thickness, and nonlinear convection flow is considered in this generalized heat flux examination. An appropriate similarity variable is implemented on the governing equations embedding the variable viscosity, thermal conductivity, and generalized Fourier's law to drive ordinary differential equations. Galerkin weighted residual approach is utilized to calculate the flow field among other flow characteristics. The novel flow features are discussed therein. Modified Fourier and multislip's parameters are seen to have downsized the velocity and temperature field greatly. Thermal and solutal buoyancy effects are more pronounced in nonlinear form compared to the linear model. Dufour number influences both velocity and energy fields positively but negates the concentration field, while the Soret number gives an opposing characterization.     

云南富宁良子老寨钛铁矿成矿规律和矿床成因

云南富宁地区钛铁矿是我国重要的钛铁矿矿床,成矿条件优越。本文对良子老寨矿区残坡积风化壳型钛铁砂矿床的地质特征、矿体、矿石特征进行了总结和研究,探讨了矿床的矿床成因和成矿规律。海西—印支期偏碱性基性钛辉辉长辉绿岩体为该区钛铁矿的形成提供了物质来源。富宁地区温热潮湿多雨气候有利于风化作用形成,岩体出露地表后,岩体中的钛矿物经风化剥离、水解作用、次生富集、原地残留或近距离搬运沉积,形成了残坡积风化壳型钛铁砂矿床。陡坡、临近河流区域矿体厚度薄,风化作用弱部位品位低;山脊缓坡、河谷阶地、地形低凹地段矿体厚度较大、品位高。本文研究成果能够指导滇东南地区残坡积物风化壳内钛矿的找矿工作。     

基于集员未知输入观测器的风力机桨距执行器故障诊断

风力机一般放置在恶劣的环境中,其桨距执行器极易出现故障。文中针对一类含有未知但有界干扰和噪声的风力机系统的桨距执行器故障问题,设计了集员未知输入观测器对桨距的执行器故障进行检测并分离。采用气动机理和现代辨识原理建立风力机系统模型,通过优化未知输入观测器设计对系统中的干扰解耦,基于中心对称多胞体估计不考虑故障时残差的区间包络,并将其作为残差估计的上下动态阈值,实现状态估计。在上述基础上提出了利用一组集员未知输入观测器进行故障诊断的策略。仿真结果表明,在实验过程中,文中所设计的集员未知输入观测器准确地诊断出了风力机桨距执行器的3阶和5阶线性系统在发生突变故障和缓慢时变故障的时间和位置,证明了所提故障诊断策略的有效性。     

Development of a probabilistic algorithm of surface residual materials on Si3N4 ceramics under longitudinal torsional ultrasonic grinding

Longitudinal torsional ultrasonic-assisted grinding (LTUG) is one of the main methods to achieve high-quality and high-efficiency machining of high-performance ceramic materials. However, it isn't easy to accurately characterize the three-dimensional (3-D) surface topography due to multiple random factors during LTUG. Aiming at the complex surface features caused by multiple random factors in the LTUG of Si3N4 ceramics, a probabilistic algorithm for the height of residual material on the surface (HRMS) in LTUG of Si3N4 ceramic was proposed, and the prediction model for the 3-D surface topography and 3-D surface roughness parameters of Si3N4 ceramics in LTUG was established by using this algorithm. Simulation and experimental results show that the prediction model of 3-D surface topography and 3-D surface roughness established by the HRMS algorithm can more realistically predict the general characteristics of 3-D surface topography in LTUG under different process parameters, and the error range of the 3-D surface roughness parameter is 0–14.07%, which realizes the high-precision and high-reliability prediction of the 3-D surface topography and 3-D surface roughness parameters of the Si3N4 ceramic under LTUG.     

Comparison of 3-breed rotational crossbreds of Montbéliarde,Viking Red,and Holstein with Holstein cows fed 2 alternative diets for dry matter intake,production, and residual feed intake

The objective of this study was to compare 3-breed rotational crossbred (CB) cows of the Montbéliarde, Viking Red, and Holstein (HO) breeds with HO cows fed 2 alternative diets for dry matter intake (DMI), fat plus protein production (CFP), body weight (BW), body condition score (BCS), feed efficiency, and residual feed intake (RFI) from 46 to 150 days in milk (DIM) during first lactation. The CB cows (n = 17) and HO cows (n = 19) calved from September 2019 to March 2020. Cows were fed either a traditional total mixed ration diet (TRAD) or a higher fiber, lower starch total mixed ration diet (HFLS). The HFLS had 21% more corn silage, 47% more alfalfa hay, 44% less corn grain, and 43% less corn gluten feed than the TRAD. The 2 diets were analyzed for dry matter content, crude protein, forage digestibility, starch, and net energy for lactation. The BW and BCS were recorded once weekly. Daily milk, fat, and protein production were estimated from twice monthly milk recording with random regression. Measures of efficiency were CFP per kilogram of DMI and DMI per kilogram of BW. The RFI from 46 to 150 DIM was the residual error from regression of DMI on milk energy, metabolic BW, and the energy required for change in BW. Statistical analysis of all variables included the fixed effects of diet, breed group, and the interaction of diet and breed group. The CB cows fed HFLS had less DMI (?12%) and lower DMI/BW (?14%) compared with the HO cows fed TRAD. For CFP, CB and HO cows were not different when fed TRAD or HFLS. Furthermore, the CB cows fed HFLS had higher BW (+50 kg) compared with HO cows fed HFLS. The CB cows fed TRAD had higher BCS than HO cows fed TRAD and HO cows fed HFLS (+0.46 and +0.62, respectively). The HO cows fed TRAD had more DMI (+14%) and lower CFP per kilogram of DMI (?12%) compared with the HO cows fed HFLS. In addition, mean RFI from 46 to 150 DIM was lower and more desirable for CB cows fed HFLS (?120.0 kg) compared with HO cows fed TRAD (85.3 kg). Dairy producers may feed either TRAD or HFLS to CB cows without loss of CFP.